1975 Vega GT

Tell everyone about the progress of your project! Please respect people's threads.

Moderator: Moderators

Re: 1975 Vega GT

Postby cjbiagi » Sun Jul 26, 2015 8:13 pm

Car is looking and sounding great. How do you plan on sealing the slip tubes on the headers?
Clyde.........75 Monza 2+2
User avatar
cjbiagi
 
Posts: 8608
Joined: Sun Jun 25, 2006 2:37 pm
Location: Glenwood, Illinois

1975 Chevrolet Monza


Re: 1975 Vega GT

Postby BadBowtie » Mon Jul 27, 2015 12:32 am

cjbiagi wrote:Car is looking and sounding great. How do you plan on sealing the slip tubes on the headers?


Its a pretty crude but works method of using header wrap for a 4" section with hose clamps on either end. I havent removed the ones on the passenger side for at least a year and they dont seem to leak at all. Before I used to have to drop my driver side tubes to change the oil filter so I didnt want to deal with a goopy sealer. Ideally I would find some type of stepped exhaust clamp with the right diameters or modify the headers to seal better but until I decide this is a less permanent solution. The hardest tube to do on the Don Hardy headers is the #1 tube that goes around the steering shaft, I've had that one blow the wrap off before, plus its a tight spot to work in.
James

1975 Vega GT sbc, Microsquirt w/Edelbrock MPFI, M21 4-speed and Ford 9"
User avatar
BadBowtie
 
Posts: 846
Joined: Wed Oct 28, 2009 12:20 am

1975 Chevrolet Vega GT

Re: 1975 Vega GT

Postby BadBowtie » Sat Aug 08, 2015 9:44 am

For the first time in what would be 4 years I drove the car and the engine temperature gauge never went higher than 180deg (180 thermostat) with my fan only on low speed. I think after all this time the problem I had was caused by poor quality automatic circuit breakers, I swapped in a set of high quality ones and they seemed to work flawlessly instead of cutting on/off constantly, sometimes leaving me half-stranded and overheating at 200deg (what happens when you have no fans in traffic).

I seem to have a decent tune-up in the car and its running really well with the crossram, pulls hard on the top end so I bumped my rev limiter up to let me shift at 6500 if I feel the engine still pulling. All I have left to do are a few small things, finish painting my hood and find an exhaust rattle that is driving me NUTS...

Also while I had the car out yesterday I finally got it weighed, half a tank of gas, in full trim, 350 sbc, M21 muncie, 9" rear, s10 swap up front, Aluminum 15" wheels, no weight reductions aside from trimming out the hood for the crossram/dual carbs was 2960 lbs. I was pretty shocked thinking the car might be lighter but this is similar to what other people on the forum have had as well.
James

1975 Vega GT sbc, Microsquirt w/Edelbrock MPFI, M21 4-speed and Ford 9"
User avatar
BadBowtie
 
Posts: 846
Joined: Wed Oct 28, 2009 12:20 am

1975 Chevrolet Vega GT

Re: 1975 Vega GT

Postby vegastre » Sat Aug 08, 2015 2:10 pm

was 2960 lbs...I was pretty shocked thinking the car might be lighter but this is similar to what other people on the forum have had as well


I looked up an old post when I did away with the 5mph bumpers and weighed at the local recycler scales and the weight was 2959 with me in it. I weigh 205 lbs...so 2754 lbs.
Phil Kennedy~
72 Chevrolet Vega GT Hatchback
75 Pontiac Astre SJ Safari Wagon
User avatar
vegastre
 
Posts: 1289
Joined: Mon Nov 10, 2008 12:10 am
Location: Dallas, Texas

1975 Pontiac Astre SJ

Re: 1975 Vega GT

Postby cjbiagi » Sat Aug 08, 2015 3:10 pm

OK, I ended up taking a small piece of thin sheetmetal and cut it to the width of two hose clamps. Then I wrapped the metal around the joint and installed the two hose clamps one on the larger tube and one on the smaller one. The clamps are strong enough to compress the sheetmetal around each tube and form a pretty good seal. So I ended up with a stepped piece of sheetmetal tightly wrapped around each tube diameter. I turned the clamps so that the screw is barely visible so it doesn't look to odd.
Clyde.........75 Monza 2+2
User avatar
cjbiagi
 
Posts: 8608
Joined: Sun Jun 25, 2006 2:37 pm
Location: Glenwood, Illinois

1975 Chevrolet Monza

Re: 1975 Vega GT

Postby BadBowtie » Sat Aug 08, 2015 11:50 pm

vegastre wrote:
was 2960 lbs...I was pretty shocked thinking the car might be lighter but this is similar to what other people on the forum have had as well


I looked up an old post when I did away with the 5mph bumpers and weighed at the local recycler scales and the weight was 2959 with me in it. I weigh 205 lbs...so 2754 lbs.


I was thinking of doing that next, that would put me much closer to where I would like it to sit weight wise, but in all reality it doesn't matter all that much since its just a street car. Maybe down the road, I would prefer sticky tires first!

cjbiagi wrote:OK, I ended up taking a small piece of thin sheetmetal and cut it to the width of two hose clamps. Then I wrapped the metal around the joint and installed the two hose clamps one on the larger tube and one on the smaller one. The clamps are strong enough to compress the sheetmetal around each tube and form a pretty good seal. So I ended up with a stepped piece of sheetmetal tightly wrapped around each tube diameter. I turned the clamps so that the screw is barely visible so it doesn't look to odd.


Sounds like a nice solution, like making your own band clamp! mine looks a little odd for one tube if you look for it, the rest are all under the car.
James

1975 Vega GT sbc, Microsquirt w/Edelbrock MPFI, M21 4-speed and Ford 9"
User avatar
BadBowtie
 
Posts: 846
Joined: Wed Oct 28, 2009 12:20 am

1975 Chevrolet Vega GT

Re: 1975 Vega GT

Postby spencerforhire » Sun Aug 09, 2015 10:09 pm

If you're looking for a way to seal up the slip joints in the header tubes, Permatex Ultra Copper RTV is safe to 700 F. Much better than exhaust joint sealing compound because it is flexible enough to get the joints back apart. I used it way back on the slip joints of my Hooker 2135's.
The "fleet"-
72 Vega HB Drag Car -383/'Glide/9"(9.35@146.19)(5.94@117.28 1/8th)
77 Vega Estate wagon- project(someday)will have TPI305/T-5, S-10 spindles/axles
76 Vega GT- 400/4spd/9" retired from active duty(rusty)
06 Silverado 2WD ex.cab daily
03 Silverado 2WD ex.cab (retired)
06 Haulin' 20ft enclosed car transporter
06 GMC Canyon Shop truck
07 Colorado project( 5.3 4L60e swap)
99 Saturn SL1- wife's car
01 Saturn SC2- son's project
07 Saturn Ion Redline project
and 4 more Saturn "parts cars"
Note- the very act of listing all of these has made me realize I have some kind of problem.....

Visit http://www.spencerforhire.ca
User avatar
spencerforhire
 
Posts: 2442
Joined: Mon Jul 03, 2006 9:02 pm
Location: Halifax, Nova Scotia

1972 Chevrolet Vega Hatchback

Re: 1975 Vega GT

Postby BadBowtie » Tue Aug 18, 2015 9:34 pm

Been running around in the vega, getting lots of comments. Mostly about the paint, I dont know why, its all a similar shade of yellow now (you can see the difference in the hood) :lol: I just tell them I cant see the color of the car when I'm inside burning rubber. Engine combination is running GREAT once I get it warmed up, cold response is pretty poor but that's normal with such a large plenum.

Not all things are good, seems like my used posi for the 9" isnt holding up well but with used/worn clutches its to be expected, this summer its been acting like an open diff so this winter I will re-build it with fresh clutches and tighten it up again. Its a good thing this wont stop me from driving the car around cause I'm having way too much fun.
You do not have the required permissions to view the files attached to this post.
James

1975 Vega GT sbc, Microsquirt w/Edelbrock MPFI, M21 4-speed and Ford 9"
User avatar
BadBowtie
 
Posts: 846
Joined: Wed Oct 28, 2009 12:20 am

1975 Chevrolet Vega GT

Re: 1975 Vega GT

Postby zeke » Tue Aug 18, 2015 11:33 pm

Another H-body returns to the streets! Sweet :dance: :th:
Chris

zeke's 79 Monza Project

zeke's 78 Sport Coupe

Photographs posted by this user (zeke) are the sole property of this poster. Any use without express written permission is prohibited
User avatar
zeke
 
Posts: 2930
Joined: Fri Jul 21, 2006 3:27 am
Location: Southern Ontario, Canada

1979 Chevrolet Monza 2+2

Re: 1975 Vega GT

Postby BadBowtie » Sat Mar 05, 2016 1:02 am

I'm due for an update!

I rebuilt my 9" posi cause the rearend kept opening up under load and darting to one side. Turns out it has an extra shim but was missing the most important friction plate that meets inside the hub, go figure how it even remotely worked for 4 years under my abuse. Hopefully everything works good this summer.
Just started on a power steering swap. Already running into potential problems! This is a lightweight 600 series CJR box, 12:1, 3 turns lock to lock. I wasnt able to get the boot off the plug but once its tightened up everything might JUST clear. I'll have to see what I can do about fittings/elbows.
You do not have the required permissions to view the files attached to this post.
James

1975 Vega GT sbc, Microsquirt w/Edelbrock MPFI, M21 4-speed and Ford 9"
User avatar
BadBowtie
 
Posts: 846
Joined: Wed Oct 28, 2009 12:20 am

1975 Chevrolet Vega GT

Re: 1975 Vega GT

Postby TimMcCabe » Mon Mar 07, 2016 6:33 pm

Hi Badbowtie,

Can you unbolt and rotate the flow control valve on the steering box so the fittings point off to the side instead of straight up?

Cheers,
Tim
1972 TPI Vega T56 6 speed

Contact me for all of your Tachometer needs
User avatar
TimMcCabe
 
Posts: 261
Joined: Thu Jun 29, 2006 1:45 pm
Location: Toronto Canada

Re: 1975 Vega GT

Postby BadBowtie » Mon Mar 07, 2016 9:07 pm

TimMcCabe wrote:Hi Badbowtie,

Can you unbolt and rotate the flow control valve on the steering box so the fittings point off to the side instead of straight up?

Cheers,
Tim


Thanks for the tip, I didn't know they could be rotated. Unfortunately that puts the fittings right into the side of the block. I think I have the fitting situation figured out that I'm going to use an OEM line thats 6-8" long, it has two tight 90 degree bends and the fittings I need. I'll cut the line right after the 90s on each side and braze each with -6an fittings to match my pump side. If that doesnt work I will at least have the right metric o-ring fittings and bring it to a hydraulic shop to get lines made up. The reason being that AN fittings/adapters are too tall off the box.

For the spark plug I'm going to try a shorter plug and/or a thinner boot. I might even have to "clearance" the box a bit :lol:
James

1975 Vega GT sbc, Microsquirt w/Edelbrock MPFI, M21 4-speed and Ford 9"
User avatar
BadBowtie
 
Posts: 846
Joined: Wed Oct 28, 2009 12:20 am

1975 Chevrolet Vega GT

Re: 1975 Vega GT

Postby BadBowtie » Sat Mar 26, 2016 6:22 pm

Simple picture update, not much going on while I wait for parts to come in. Not fully committed to cutting the rest of my steering shaft until I know the steering box fittings will fit.

Sparkplug look like it will work a lot better. Accel 0437-S
2016-03-25 12.49.17.jpg

The power steering hose/fitting I got has the wrong flared end but I found what I need from edelmann 39109/10 for the 18mm end and 29106/7 on the 16mm end. Going to order this week since I have the -6AN weld on fittings ready to go.
2016-03-25 13.07.27.jpg

31UvOLYsoyL._SX355_.jpg

On the plus side I got the steering pump mocked up, everything lines up nicely.
2016-03-26 17.31.12.jpg
You do not have the required permissions to view the files attached to this post.
James

1975 Vega GT sbc, Microsquirt w/Edelbrock MPFI, M21 4-speed and Ford 9"
User avatar
BadBowtie
 
Posts: 846
Joined: Wed Oct 28, 2009 12:20 am

1975 Chevrolet Vega GT

Re: 1975 Vega GT

Postby BadBowtie » Thu Apr 07, 2016 7:58 pm

Moving along, next step is to paint the front end parts, mount everything up and get power steering lines made up.

2016-04-03 16.15.47.jpg

2016-04-07 18.50.31.jpg

2016-04-07 18.53.58.jpg
You do not have the required permissions to view the files attached to this post.
James

1975 Vega GT sbc, Microsquirt w/Edelbrock MPFI, M21 4-speed and Ford 9"
User avatar
BadBowtie
 
Posts: 846
Joined: Wed Oct 28, 2009 12:20 am

1975 Chevrolet Vega GT

Re: 1975 Vega GT

Postby avewhtboy » Thu Apr 07, 2016 9:52 pm

I am looking at installing power steering on my car but I have the front plate motor mounts and alternator where yours it.

I am interested in what you used for the pump bracket to mount it on the passenger side. I think that's what I need to do or
have to replace the motor mounts.

Looks like a lot of work but will be worth it when done.

Are you happy with your brakes? I notice you have manual rather than power brakes.

Nice car!
User avatar
avewhtboy
 
Posts: 573
Joined: Thu Sep 24, 2009 11:06 am
Location: Stone Mountain Georgia

PreviousNext

Return to Project Journals

Who is online

Users browsing this forum: No registered users and 13 guests