Fiberglass hatch on a street car

Moderator: Moderators

Fiberglass hatch on a street car

Postby 71V8Vega » Sat Feb 25, 2017 4:04 pm

I'm looking for a substitute for a stock steel hatch. I'm not concerned with weight, its just been difficult to find a hatch in my area that someone is looking to sell. Does anyone have a fiberglass hatch on their Vega? I was curious how the fit and finish is. Also do they seal up to weatherstripping? I would like to know if they work well on a street car. I have my own guess of how a fiberglass hatch might fit and seal up, but I wanted to hear from someone who has one. The only hatch I have seen with a structure underneath similar to a stock hatch was one from Showcars Unlimited and I have read plenty of bad reviews about that company.
71V8Vega
 
Posts: 5
Joined: Tue Sep 18, 2012 12:32 pm


Re: Fiberglass hatch on a street car

Postby spencerforhire » Sat Feb 25, 2017 5:15 pm

The one on my drag car and any others I have seen are all too flimsy to seal against wind or water leaks. Unlike hoods, I doubt if there are any "street weight" hatches available.
The "fleet"-
77 Vega Estate wagon- project(someday)will have TPI305/T-5, S-10 spindles/axles
72 Vega HB Drag Car -383/'Glide/9"(9.35@146.19)(5.94@117.28 1/8th)
76 Vega GT- 400/4spd/9" retired from active duty(rusty)
03 Silverado 2WD ex.cab (work truck/parts hauler)
04 Silverado 2WD ex.cab (retired)
06 Haulin' 20ft enclosed car transporter
93 Suburban- 350/4L60(retired)
00 Saturn SW2- wife's car
01 Saturn SC2- younger son's project
00 Saturn SL2- daughter's car
98 Saturn SW2- spare
and 3 more Saturn "parts cars"
Note- the very act of listing all of these has made me realize I have some kind of problem.....

Visit http://www.spencerforhire.ca
User avatar
spencerforhire
 
Posts: 2404
Joined: Mon Jul 03, 2006 9:02 pm
Location: Halifax, Nova Scotia

1972 Chevrolet Vega Hatchback

Re: Fiberglass hatch on a street car

Postby 71V8Vega » Sat Feb 25, 2017 6:18 pm

Thanks for the quick response. Most of the fiberglass hatches I've seen are designed to be pinned on a race car. Your reply is what I expect everyone will say on this subject
71V8Vega
 
Posts: 5
Joined: Tue Sep 18, 2012 12:32 pm

Re: Fiberglass hatch on a street car

Postby cjbiagi » Sat Feb 25, 2017 8:34 pm

I would try and find a good used hatch or repair what you have. I doubt a fiberglass would be too good on a street car.
Clyde.........75 Monza 2+2
User avatar
cjbiagi
 
Posts: 8035
Joined: Sun Jun 25, 2006 2:37 pm
Location: Glenwood, Illinois

1975 Chevrolet Monza

Re: Fiberglass hatch on a street car

Postby Monza Harry » Sat Feb 25, 2017 8:35 pm

I would like to add to Spencers responce, the factory uses lots of these and hoods these days, so it can be made to work. However most that you will buy from the aftermarket will be as Spencer reported, but if you are willing to work on it you could remove any bracing [or order with it unbonded if going {aftermarket} factory direct & new] then add a layer or two of glass and resin to both the shell and inner. If it is only an outer skin do the same and add a layer and build you own inner and you could add some tubing or hardwood frame and "Glass it over" Just some fodder for consideration. Harry P.S. Same time responce as "Clyde"
I'm not a hoarder I'm a preservationist 78 Monza Spyder (Soon To Be 2+2 with Spoilers)
User avatar
Monza Harry
 
Posts: 2189
Joined: Tue Oct 04, 2011 8:50 am
Location: Windsor ON Canada

1978 Chevrolet Monza 2+2

Re: Fiberglass hatch on a street car

Postby KZVEGA » Mon Feb 27, 2017 10:03 pm

I have a showcars hatch on mine. The reviews are spot on about the guy unless....you buy from him on eBay. EBay runs very tight protection so he has to play by the rules. As for the hatch, it's not bad....for fiberglass. I had to do some heating and clamping to get it close. I wasn't looking for show car finish for mine it's mainly a drag car. I liked that it was bolt on. Not sure on how it seals still have to paint mine before I put seals on but I think it will be okay. It latches so it's fine by me.
KZVEGA
 
Posts: 139
Joined: Mon Aug 12, 2013 7:04 pm
Location: Chicago, IL

Re: Fiberglass hatch on a street car

Postby 71V8Vega » Thu Mar 16, 2017 11:24 pm

thanks guys for the great advice!

I put an add on craigslist looking for an original steel hatch and I've been getting a call a week from someone who has one. It seems there may be more of them out there than I thought.
71V8Vega
 
Posts: 5
Joined: Tue Sep 18, 2012 12:32 pm


Return to Racing Chassis

Who is online

Users browsing this forum: No registered users and 1 guest