My mini tub job

Moderator: Moderators

Re: My mini tub job

Postby monzaz » Thu Dec 06, 2018 8:39 pm

Fasterthansome wrote:Wow thats alot of work to tuck a 26" tire. I'm lazy I would just stick a 9" tire under it. :D Or mini tub it for a 28x10.


Here is 8" wide slick pulling the front tires...I do not think MOST need to do it for drag racing.... For looks I like it.
this is with a destroked 430 hp SBC 377 with 5000 stall leaving at 3400 chip 26 x 8" mickey Thompson slicks

So this is 10.50 car But it is ladder bar rear suspension just incase your trying to pull them with stock torque arm rear...lol

406 716 Hp 708 FT LBS torque going in soon and I think these 8" slicks are not going to make it ... :( Yes I will be in the tub rear too soon.... BUT I am going to try to see how much 8" 26" tall slicks CAN HANDLE...Soon.
Oh and this is a 10 bolt 8.5 S10 Full spooled rear 3.90 gear rear

Jim
J D Race
Attachments
big monza up 6.png
big monza up 6.png (249.79 KiB) Viewed 162 times
J D Race & Restoration
Richfield, Oh
JDRACE.COM
User avatar
monzaz
 
Posts: 627
Joined: Tue Nov 14, 2006 11:26 am
Location: Richfield, Oh


Re: My mini tub job

Postby chevyart » Fri Dec 07, 2018 2:53 pm

jim 406 cu in 716 HP sounds like you are using juice.. i run a 377 (aprox 600 HP and a 383 (aprox 650HP) and no juice((950 holley on each) and the 377 revs different for sure than the 383. love both engines, but the 383 is the obvious winner. like your car and choice on engines art in NY
chevyart
 
Posts: 1861
Joined: Fri Oct 27, 2006 10:00 pm

Re: My mini tub job

Postby chevyart » Fri Dec 07, 2018 2:55 pm

PS i know you build the rears and to see the 10 bolt hold up is a real tribute to your ability to build these differentials. art
chevyart
 
Posts: 1861
Joined: Fri Oct 27, 2006 10:00 pm

Re: My mini tub job

Postby monzaz » Fri Dec 07, 2018 7:14 pm

No JUICE? I have never used NOS on any motor yet. Got a NEW guy building my motors...

We were shooting for 600 - That is not even ported heads.
Stock gasket matched Dart Pro 1 hears 215 runners and 2.05 IN valve with 1.60 ex. Valve
Victor Jr.
850 carb (brawler Carb) or something like that...Out of the box only did 82 and 82 jetting No Power valve as we drag race only
MSD old school 6AL ... not even digital

We dynoed it again a week later after squaring up the jets and ran 730 hp but lost about 3-4 Foot Lbs over all... ??? I di dnot get those sent over to me yet to post
Remember this is a DRAG race motor not for the street. Jim
Attachments
406 monza dyno HP and Torque numbers small.jpg
406 monza dyno HP and Torque numbers small.jpg (64.35 KiB) Viewed 142 times
406 Monza engine dyno graph small.jpg
406 Monza engine dyno graph small.jpg (60.42 KiB) Viewed 142 times
J D Race & Restoration
Richfield, Oh
JDRACE.COM
User avatar
monzaz
 
Posts: 627
Joined: Tue Nov 14, 2006 11:26 am
Location: Richfield, Oh

Previous

Return to Racing Chassis

Who is online

Users browsing this forum: No registered users and 1 guest