Page 1 of 1

L-88 vega hood (fiber concepts)

PostPosted: Wed Apr 04, 2007 4:09 pm
by peterpan
http://www.fiberpartsconcepts.com/

i bought my L-88 vega hood here and am very pleased with it

in these pics the hood is not bolted on its just sitting on there

PostPosted: Thu Mar 06, 2008 4:29 pm
by peterpan
they now show a cowl hood on there site for the vega

PostPosted: Thu Mar 06, 2008 4:33 pm
by spyder_xlch
That is a nice looking hood. (the L-88)

PostPosted: Thu Mar 20, 2008 7:55 pm
by jdandboo@hotmail.com
mmm,wish they made one for my monza,,,I think theres a place in Pa that does custom's,,gonna have to take a drive one day(after the credit cards are a bit lower)

PostPosted: Thu Mar 20, 2008 8:30 pm
by spyder_xlch
jdandboo@hotmail.com wrote:mmm,wish they made one for my monza,,,I think theres a place in Pa that does custom's,,gonna have to take a drive one day(after the credit cards are a bit lower)
Where's that?

PostPosted: Thu Mar 20, 2008 8:32 pm
by jdandboo@hotmail.com
i read one somewhere here on the forum,,unfortunately i think it was gonna cost like $500+ shipping,,therefore-the ride out there,lol

Re: L-88 vega hood (fiber concepts)

PostPosted: Thu Jun 19, 2008 3:57 pm
by peterpan
i paid $350 for my hood and after shipping it was like $560 to wyoming

Re: L-88 vega hood (fiber concepts)

PostPosted: Tue Apr 27, 2010 7:23 pm
by djv8ga
I bought (Finally) a Cowl Induction hood from this guy. The service was excellent and the hood is awesome. I will post pics soon.

Re: L-88 vega hood (fiber concepts)

PostPosted: Mon Jan 17, 2011 9:53 pm
by cfar
I just got mine -super guy and nice hood

Re: L-88 vega hood (fiber concepts)

PostPosted: Sun Jul 31, 2011 12:54 pm
by robsta11111
peterpan wrote:http://www.fiberpartsconcepts.com/

i bought my L-88 vega hood here and am very pleased with it

in these pics the hood is not bolted on its just sitting on there


would you give me a measurement from under the scoop to a straight edge across the fenders? I like that hood but have a tunnet ram and 2-4's. They dont stick out crazy high so might clear that hood

Re: L-88 vega hood (fiber concepts)

PostPosted: Sat Jun 15, 2013 7:53 am
by dadhad1
I wasn't that happy with mine. If you're ok with the hood not lining up to fenders/header panel, you might be happy with this hood.
But be warned, if you are expecting nice show quality lines, don't expect to bolt this on and be satisfied.
I ended up grafting the L-88 glass feature part of the hood on a stock metal hood. This provided for a VERY nice finished product because it had nice factory fit/finish/gapping and the L-88 feature in the middle. I cut a nice big circle in the steel hood to make functional use of the added L88 clearance and for engine heat venting.
I would also recommend strengthening the center/rear most bridge areas both top & bottom. The glass was VERY thin/weak in these areas, in fact, it was cracked when it arrived. I added braces on bottom to support latch loop to and the top to provide much needed rigidity that it needed.

That's my 2 cents...

Re: L-88 vega hood (fiber concepts)

PostPosted: Fri Dec 20, 2013 5:44 pm
by RED73V8
From what I understand is that they supplied the original L-88 hoods for the Motion vegas - I plan on puting one on my &3 Hatchback soon

Re: L-88 vega hood (fiber concepts)

PostPosted: Fri Dec 20, 2013 6:02 pm
by 454Vega
RED73V8 wrote:From what I understand is that they supplied the original L-88 hoods for the Motion vegas - I plan on puting one on my &3 Hatchback soon


Yes,the guy that did them for motion is doing them still at fiber concepts.

Re: L-88 vega hood (fiber concepts)

PostPosted: Fri Dec 20, 2013 7:25 pm
by T-FATTY
I have the cowl hood, its nice. Its not on the car yet but it seems well made, as far a fit as long as its close im good.