Kick panel/interior leakage...

Tips, tricks, tools...

Moderator: Moderators

Kick panel/interior leakage...

Postby Ssshazam » Tue Jun 09, 2015 6:42 pm

My "new to me" 1972 Notchback has standing water beneath the pedals and behind the driver's seat after heavy rainfall. I traced the dampest carpet areas to the driver's kick panel, removed it and reached behind to find damp leaves and crud collected within at the bottom of the fender. This car was purchased as a restored salvage; is something missing to prevent rain/debris from falling within the fender; perhaps an additional seal other than the straight seal running along the width beneath the hood?
Ssshazam
 
Posts: 2
Joined: Tue Jun 09, 2015 6:27 pm


Re: Kick panel/interior leakage...

Postby Kenova » Tue Jun 09, 2015 9:02 pm

That is very common. You can keep some of the bigger crap out of there by fabricating
screens to cover the cowl area under the rear edge of the hood.
It would also prevent sockets and wrenches from disappearing down inside your fenders. :wink:

Ken
My other car is a Nova.
User avatar
Kenova
 
Posts: 1546
Joined: Sun Jul 02, 2006 9:46 pm
Location: Ontario, Canada

Re: Kick panel/interior leakage...

Postby cjbiagi » Tue Jun 09, 2015 10:37 pm

You need to keep the lower fenders clean from debris so the water can drain out. I covered my cowl area with mesh, although I did it more for looks but it will also keep leaves and crap from clogging things up. A good cowl seal seal is also important to help keep debris out and also prevent hot engine compartment air from entering the the interior through the kick panel vents. I have a replacement cowl seal available if anyone needs it. http://www.ebay.com/itm/141688476145?ss ... 1555.l2649 Here's a pic of my screens. cjbiagi@yahoo.com
Attachments
cowl screen.jpg
cowl screen.jpg (189.98 KiB) Viewed 375 times
Clyde.........75 Monza 2+2
User avatar
cjbiagi
 
Posts: 8035
Joined: Sun Jun 25, 2006 2:37 pm
Location: Glenwood, Illinois

1975 Chevrolet Monza

Re: Kick panel/interior leakage...

Postby Ssshazam » Tue Jun 09, 2015 11:04 pm

Thanks for the timely replies; I indeed removed quite a bit of debris after removing the kick panel. Next, screen fabrication! Thanks for the tip!
Ssshazam
 
Posts: 2
Joined: Tue Jun 09, 2015 6:27 pm

Re: Kick panel/interior leakage...

Postby 67shovel » Wed Jun 10, 2015 8:14 am

Might as well pull the passenger side kick panel and clean it out too.
79 Monza wagon Pro street, cage tubs narrowed 9
73 GT Vega wagon street car 355 700r4 a/c
68 RS Z/28 302
67 SS 396
Cobra replica
65 Corvair Corsa midengine 301
http://pictures.sprintpcs.com/share.do? ... =RETRIEVED
67shovel
 
Posts: 289
Joined: Tue Jul 19, 2011 8:29 am
Location: Houston Tx

Re: Kick panel/interior leakage...

Postby cosvega76 » Wed Jun 10, 2015 8:43 am

Another thing to keep in mind for a leak on the driver's side is to check the grommet where the hood cable enters the passenger compartment. Rain will follow the cable down and drip on the floor if the grommet is broken or missing.


Chuck
cosvega76
 
Posts: 2391
Joined: Mon Jul 03, 2006 8:36 am
Location: Moscow Mills, MO

1973 Chevrolet Vega GT

Re: Kick panel/interior leakage...

Postby bugdewde » Wed Jun 10, 2015 10:42 am

I've removed the bolts on the bottom of the fender and some along the door jamb to allow me to open the bottom of the fender for a r eak good clean out. Also, the cowl wall behind the fender can be inspected for rust.. I like to clean/scrape it and paint it or coat it to prevent rust. I've seen these cowl walls with rust holes in them.
Dwight

'73 Vega GT Hatchback, mostly stock....
'72 Vega GT Kammback, 215 V8
'73 Vega Wagon - Currently in Limbo....
My rides: http://www.cardomain.com/id/bugdewde
User avatar
bugdewde
 
Posts: 2093
Joined: Mon Jun 26, 2006 7:08 pm
Location: East Tennessee

1972 Chevrolet Vega Kammback GT

Re: Kick panel/interior leakage...

Postby cos2482 » Thu Jun 11, 2015 10:40 pm

Over the years with many Vegas and leaks on the drivers side, you may want to check above the rubber grommet that Cosvega76 mentions. You can feel all the way to that grommet through the upper cowel. I have had my driver side floor board filled with water that ran down the hood release handle during a single heavy rain. The hard plastic cable sheathing with age will crack where it makes a 145 degree turn inside the cowel cavity before that rubber grommet. The way it is designed, water will travel down that sheathing into the crack and follow the cable to the release handle. Beside the lower cavity in the fender cowel being filled with debris, I would also check that cable.
It happened on three different Vegas that I had owned. I repaired them back then by replaceing the cable, and later on with out spare parts, I pulled the cable out and used electrical shrink tubing over the crack which also seemed to work out fine.
Jim
http://blog.hemmings.com/index.php/2007 ... ves-vegas/

1973 Vega GT Hatchback (Millionth Vega)
1975 Vega GT Kammback (Nomad modification)
1976 Vega GT Hatchback (stock)
1976 Vega Cosworth (white/white, stock)
1977 Vega Estate (stock)
1977 Vega Hatchback (stock, bought new)
2011 Ford Ranger XLT (2,3 twincam 5spd std)
2000 Ford ranger XLT (2,5L 5spd std)
2003 Chevrolet Tracker (LT)
2015 Chevrolet Trax LTZ AWD
User avatar
cos2482
 
Posts: 298
Joined: Wed Jun 28, 2006 7:16 pm
Location: East Greenbush, NY


Return to Restoration Tips

Who is online

Users browsing this forum: No registered users and 0 guests