Rust removal with electrolysis

Best technical articles on the forums. Send nominations to the admins. You can reply to topics but only admins can make new ones.

Moderator: Moderators

Rust removal with electrolysis

Postby starfire383 » Sun Jul 16, 2006 7:14 pm

Hello all

There was a post on the other forum, think the title was better living through chemistry. It was about using electrolysis to descale a rusty gas tank.

Bottom line, one of the best restoration posts I have ever seen on any forum, ever. And my old shortcut indicates that EZ-Gone, I mean EZ-Board, has eliminated it.

If the originator of that post would re-post it here on the resto forum, you'd be the man. If somebody else would put up an archived copy, you would also be the man. Not quite as "the man" as the originator, but close :lol:

User avatar
Posts: 952
Joined: Tue Jul 04, 2006 4:06 pm

Postby barebonesracecars » Sun Jul 16, 2006 8:18 pm

Tim McCabe posted it originally, but below is another version I had saved from an internet site:

http://antique-engines.dickerson-design ... ectrol.asp

Rust Removal using Electrolysis

Taking advantage of common household cleaning products, items many of us have laying around the garage, kitchen or laundry room, and some science, you can clean parts from a single bolt up to an entire trailer frame through a process known as "electrolysis".
What you need:
• A non-conducting container - a large plastic bucket works really well.
• Battery charger - big is better, however even one able to produce 6 to 10 amps should do. A student recently used my site as the basis for a school project and used a computer power supply in place of battery charger.
• Sacrificial electrodes. Concrete reinforcing rod works well (rebar) cut into lengths about 4" taller than your bucket or container. Do not use stainless steel! The results are a health hazard and illegal (more on that later)
• Arm and Hammer LAUNDRY soda, also called washing soda.
• Wire and/or cables for connecting electrodes together.
• Water.
• Small lengths of small chain (used to suspend the rusty parts in solution) or some other means to suspend the part to clean into the solution.

Loosen that stuck piston with your soft drink?
Using a plastic, or non-conductive bucket (not metal), mix a solution of 5 gallons water to 1/3 to 1/2 cup laundry soda. Mix well so all soda is dissolved. Do not try to use other salts. You won't get better results and dangerous effects may occur. Caustic soda, for example, is far too corrosive. Solutions of ordinary table salt can generate chlorine gas (toxic) at the positive electrode (anode).
Clean the electrodes so they aren't too rusty - especially at the top ends - they need to make good electrical contact with your wire or cable AND with the water. I take mine to a wire wheel and give them just a real quick going over. Place electrodes in bucket around sides, so the clean, rust free ends stick up above the bucket. Use clamps or some means to hold them in place around the perimeter of the inside of the bucket or container so that they cannot move freely or fall into center of bucket. The electrodes must not touch the part(s) to be cleaned, which will be suspended in center of bucket. I use small C clamps. Whatever you use, it shouldn't be copper, and will get a bit messy if it gets into your cleaning solution.
Tie the electrodes together with wire or cables. I use copper wire twisted around the top ends, and have used old jumper cables. All electrodes need to be tied together "electrically". This will become the "anode" grid. Since the cleaning process is somewhat "line of sight" it's best to surround the part to be cleaned to some extent with the electrodes.
Suspend part to be cleaned into bucket so it hangs in the middle, not touching bottom, and not touching electrodes. I place a piece of rebar across top of bucket (see photo below) and bolt a small piece of chain to my part to be cleaned, and clamp the chain on the rod so that the chain hangs from the rod, and suspends the part into solution below. The part to clean then becomes the "cathode".
Attach battery charger - place NEGATIVE LEAD (this is critical!!) on the piece that is to be cleaned. Attach POSITIVE, or RED lead of charger, to electrode "grid" formed when you placed electrodes, or rods, into bucket and tied them all together.
Make sure electrodes and part to be cleaned are not touching each other, then turn on charger. Within seconds, you should see a lot of tiny bubbles rising from the part suspended in the mixture. Do not do this inside, or in a closed area - those bubbles are the component parts of water - H2O - hydrogen and oxygen. Remember the Hindenburg?
See how the rust and bubbles are attracted to the electrodes in the photo below? You will need to clean them from time to time - they will get covered with gunk; in fact, after many uses, they will have eroded down and need to be replaced. That is why I use rebar - it's easy to get, cheap, and most of all - SAFE FOR YOU and your environment! You can pour the waste solution on the lawn and it won't hurt it. Do watch out for ornamental shrubs, which may not like iron rich soil, however. No use making your spouse mad!
How large an item can you clean? Well, it's up to your imagination, your budget - because it takes water, your time and wife's patience. Terry Lingle demonstrated this process on a very large scale using a tank made of plywood and lined with plastic, a DC welder for power supply and hundreds of gallons of water. You will need to use more electrodes with larger parts and a larger "tank".

Safety Precautions:
- Make sure no spills can get to the battery charger. (electrocution potential as with any electric appliance)
- The leads from the charger are relatively safe, but you may still get a bit of a shock if you put your hands in the solution or touch the electrodes while the charger is running.
- Turn off the current before making adjustments to the setup. Just as a "spark" can cause a charging battery to explode in your face, this process produces similar gases because this process splits water into hydrogen gas (at the negative electrode) and oxygen at the positive electrode).
- Hydrogen will burn explosively if ignited. All flames, cigarettes, torches, etc. must be removed from the area, and sparks caused by touching the leads together must be avoided. The work should be performed outside or in a well ventilated area to remove these gases safely.
- Washing soda solutions are alkaline and will irritate the skin and eyes. Use eye protection and gloves. Immediately wash off any solution spilled or splashed onto your body.

*1979 Buick Skyhawk SCCA/street/show*
(with Buick 350 power on deck)
User avatar
Posts: 979
Joined: Sun Jun 25, 2006 3:40 pm
Location: Union County, Ohio

1979 Buick Skyhawk

Postby peterpan » Thu Sep 21, 2006 12:22 am

just getting this back to the top
User avatar
Posts: 1786
Joined: Mon Jun 26, 2006 11:51 pm
Location: rock springs wyoming

1972 Chevrolet Vega

Postby zeke » Thu Sep 21, 2006 1:16 pm

Excellent information! Will have to try that out someday. Prob great for small parts that r hard to blast or too easily damaged.
User avatar
Posts: 2609
Joined: Fri Jul 21, 2006 3:27 am
Location: Southern Ontario, Canada

1979 Chevrolet Monza 2+2

Postby ozzymoose » Fri Sep 22, 2006 2:26 am

Can be varied in size as needed, just keep a similar soda ratio and make sure your power supply is up to it or be willing to wait a bit longer! :D
You do not have the required permissions to view the files attached to this post.
If it aint broke hit it with a sledge hammer!!
User avatar
Posts: 125
Joined: Fri Jul 14, 2006 2:06 pm
Location: Melbourne

Postby markl » Sat Dec 23, 2006 6:55 pm

Hey all, Justed wanted to say this process works great! A little time consuming if your in a hurry but it works! I use Rubbermaid tubs for my tank. You can find them in so many sizes. I use wooden dowel rods laid across the top of the tub to tie off and support the piece im derusting. In my area it was a little hard finding the washing soda.
User avatar
Posts: 165
Joined: Fri Jun 30, 2006 3:36 pm
Location: Tacoma Washington

1975 Chevrolet Vega

Return to Best Of

Who is online

Users browsing this forum: No registered users and 1 guest